ultimaker_3_extended:ultimaker_3_extended

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
ultimaker_3_extended:ultimaker_3_extended [2019/09/23 02:08]
formlab [Every 3 months]
ultimaker_3_extended:ultimaker_3_extended [2020/06/23 04:11] (current)
formlab
Line 1: Line 1:
 ====== Ultimaker 3 Extended ====== ====== Ultimaker 3 Extended ======
 {{:ultimaker_3_extended:ultimaker_3_extended.png?nolink&200|}} {{:ultimaker_3_extended:ultimaker_3_extended.png?nolink&200|}}
 +
 +
 +  * Max Build Volume: ''215 x 215 x 300mm''
 +  * [[:Filament options]]
 +
 +[[:How much does FDM printing cost?]]
 +
 +----
  
 ===== Maintenance ===== ===== Maintenance =====
-==== Monthly ====+==== Every 2 months ====
   * [[https://ultimaker.com/en/resources/23131-clean-the-printer|Clean printer]]   * [[https://ultimaker.com/en/resources/23131-clean-the-printer|Clean printer]]
 +    * wash build plate with warm water
 +    * heat up nozzles to 150°C and remove plastic stuck on the nozzle (with tweezers or a paper towel)
 +    * clean Bowden tube by pushing a piece of sponge trough. Tight fit, and a new piece of sponge per tube.
   * [[https://ultimaker.com/en/resources/23130-lubricate-the-axles|Lubricate axles]]    * [[https://ultimaker.com/en/resources/23130-lubricate-the-axles|Lubricate axles]] 
 +      * clean all smooth axles with a paper towel
 +      * one drop of Unilube on all smooth axles (also the two vertical ones). Move the print head and bed manually to distribute.
  
  
-==== Every months ====+==== Every months ====
   * [[https://ultimaker.com/en/resources/52500-check-for-play-on-axles|Check for play on axles]]   * [[https://ultimaker.com/en/resources/52500-check-for-play-on-axles|Check for play on axles]]
 +      * [[https://ultimaker.com/en/resources/50871-check-for-play-on-axles|calibrate axles if play detected]]
   * [[https://ultimaker.com/en/resources/39664-check-the-tension-of-the-short-belts|Check tension of short belts]]   * [[https://ultimaker.com/en/resources/39664-check-the-tension-of-the-short-belts|Check tension of short belts]]
-  * [[https://ultimaker.com/en/resources/52501-check-for-residue-in-the-front-fan-of-the-print-head|Check for residue in front fan of print head]]+  * [[https://ultimaker.com/en/resources/50869-check-for-residue-in-the-front-fan-of-the-print-head|Check for residue in front fan of print head]]
   * [[https://ultimaker.com/en/resources/52502-check-the-quality-of-the-silicone-nozzle-cover|Check quality of silicone nozzle cover]]   * [[https://ultimaker.com/en/resources/52502-check-the-quality-of-the-silicone-nozzle-cover|Check quality of silicone nozzle cover]]
   * [[https://ultimaker.com/en/resources/23132-clean-the-print-cores|Clean print cores]]   * [[https://ultimaker.com/en/resources/23132-clean-the-print-cores|Clean print cores]]
Line 17: Line 31:
 ==== Yearly ==== ==== Yearly ====
  
 +  * [[https://ultimaker.com/en/resources/52504-clean-the-feeders|Clean feeders]] 
 +  * [[https://ultimaker.com/en/resources/52505-replace-the-bowden-tubes|Replace Bowden tubes]]
  • ultimaker_3_extended/ultimaker_3_extended.1569229685.txt.gz
  • Last modified: 2019/09/23 02:08
  • by formlab