ultimaker_3_extended:ultimaker_3_extended [Instructions]

ultimaker_3_extended:ultimaker_3_extended

01_montage_-_arrows.jpg
800×288
2020/03/30 11:40
59.7 KB
02_setup_mesh_-_collage_-_arrows.jpg
800×312
2020/03/31 04:00
93.9 KB
03_delete_geometry_-_bool_-_collage_-_arrows.jpg
800×266
2020/03/31 06:01
49.5 KB
03_delete_geometry_-_loose_-_collage_-_arrows.jpg
1180×414
2020/03/31 06:11
137.2 KB
03_delete_geometry_-_relax.gif
800×205
2020/04/01 05:14
215.3 KB
04_hole_fill_-_01_small_-_collage_-_arrows.jpg
800×272
2020/03/31 07:09
47 KB
04_hole_fill_-_02_medium_-_delete_-_collage_arrows.jpg
800×212
2020/04/01 00:44
62.8 KB
04_hole_fill_-_03_medium_-_fill_arrows.jpg
800×218
2020/04/01 06:11
52 KB
05_hole_retexture_-_collage_arrows.jpg
800×307
2020/04/01 06:48
95.6 KB
06_big_hole_-_gridfill_-_09_edge_cleanup_collage_arrows.jpg
800×258
2020/04/06 06:28
183.6 KB
06_big_hole_-_gridfill_filled_-_arrows.jpg
800×170
2020/04/06 03:21
184.6 KB
06_big_hole_-_gridfill_selection_-_arrows.jpg
800×170
2020/04/06 03:06
52.5 KB
06_big_hole_-_manual_collage.jpg
800×282
2020/04/07 01:14
219.6 KB
06_big_hole_-_manual_comparison_collage_arrows.jpg
800×198
2020/04/07 01:51
168 KB
07_normals_outside_collage_orig_arrows.jpg
800×304
2020/04/07 06:50
158.5 KB
blender-split-in-half_01.jpg
1000×565
2020/01/27 06:14
47.7 KB
blender-split-in-half_02.jpg
1000×572
2020/01/27 06:14
49.5 KB
blender-split-in-half_03.jpg
1000×572
2020/01/27 06:14
49.7 KB
blender-split-in-half_04.jpg
1000×513
2020/01/27 06:14
31.1 KB
blender-split-in-half_05.jpg
1000×572
2020/01/27 06:14
49.5 KB
blender-split-in-half_06.jpg
1000×572
2020/01/27 06:14
44.8 KB
blender-split-in-half_07.jpg
1000×572
2020/01/27 06:14
48.5 KB
blender-split-in-half_08.jpg
1000×572
2020/01/27 06:14
46.9 KB
blender-split-in-half_09.jpg
1000×572
2020/01/27 06:14
50.4 KB
blender-split-in-half_10.jpg
1000×572
2020/01/27 06:14
111 KB
blender-split-in-half_11.jpg
1000×572
2020/01/27 06:14
119.5 KB
blender-split-in-half-3d-printed.jpg
800×765
2020/01/27 06:14
89.2 KB
clean-up-glitch-01.jpg
800×600
2020/02/18 03:55
62.1 KB
clean-up-glitch-02.jpg
800×600
2020/02/18 03:57
67.9 KB
clean-up-glitch-03.jpg
800×600
2020/02/18 03:55
57.5 KB
lazy_rig_01.jpg
800×423
2020/05/18 02:39
280.7 KB
lazy_rig_02.png
722×408
2020/05/18 01:56
126.8 KB
normals_01_reduce_collage_arrows.jpg
800×266
2020/04/15 06:11
179.4 KB
normals_02_uv_mark_seam_collage_arrows.jpg
800×344
2020/04/15 07:55
277.3 KB
normals_02_uv_unwrap_arrows.jpg
800×323
2020/04/15 08:33
387.5 KB
partial-decimation.jpg
800×481
2022/09/26 07:20
77.7 KB
remesh_non_manifold_edges.png
1108×992
2021/10/13 00:40
386.4 KB
remesh_remeshed.png
953×954
2021/10/13 00:40
331 KB
remesh_settings.png
414×197
2021/10/13 00:40
21.2 KB

Date:: 2020/01/27 06:14
Filename:: blender-split-in-half-3d-printed.jpg
Format:: JPEG
Size:: 89KB
Width:: 800
Height:: 765

References for:: split_object_in_half_to_3d-print_hollow_sides

ultimaker_3_extended/ultimaker_3_extended.txt
Last modified: 2020/06/23 04:11
by formlab