projet_cjp_660:blender_workflow_for_color_printing

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Last revision Both sides next revision
projet_cjp_660:blender_workflow_for_color_printing [2020/02/21 06:25]
formlab
projet_cjp_660:blender_workflow_for_color_printing [2020/02/21 06:25]
formlab
Line 1: Line 1:
 ====== Blender workflow for color printing ====== ====== Blender workflow for color printing ======
  
-  * **In Blender:** +===== In Blender: ===== 
-    * Do your generic 3D print prep work + 
-    * UV-Unwrap the object. +  * Do your generic 3D print prep work 
-      * It's best to use a manual unwrapping method (mark edges) as the smart UV unwrap leaves visible marks on the texture. <wrap hi>(Although this might be solved when increasing the gap between islands)</wrap> +  * UV-Unwrap the object. 
-      * Make sure to have large gaps between islands <wrap hi>(can a safe minimum be calculated?)</wrap> +    * It's best to use a manual unwrapping method (mark edges) as the smart UV unwrap leaves visible marks on the texture. <wrap hi>(Although this might be solved when increasing the gap between islands)</wrap> 
-    * Open the texture and lay out the UV (or use Cycles to bake the 3D view to the texture) +    * Make sure to have large gaps between islands <wrap hi>(can a safe minimum be calculated?)</wrap> 
-      * A texture of 2048x2048px should work fine for medium sized objects. Alpha enabled, 32 bit float unchecked. +  * Open the texture and lay out the UV (or use Cycles to bake the 3D view to the texture) 
-    * Save as a PNG file, so it's external to the project. +    * A texture of 2048x2048px should work fine for medium sized objects. Alpha enabled, 32 bit float unchecked. 
-    * connect your texture to the **Principaled BSDF shader**, and the shader to the material surface output. This might look bad, but otherwise the texture is not linked in the exported .mtl file. +  * Save as a PNG file, so it's external to the project. 
-      * https://blender.stackexchange.com/questions/149081/mtl-file-after-exporting-comes-without-texture-map-map-kd +  * connect your texture to the **Principaled BSDF shader**, and the shader to the material surface output. This might look bad, but otherwise the texture is not linked in the exported .mtl file. 
-    * Export as OBJ & set Path type: copy (blender copies texture file to destination folder) +    * https://blender.stackexchange.com/questions/149081/mtl-file-after-exporting-comes-without-texture-map-map-kd 
-  * **In 3D Sprint:**  +  * Export as OBJ & set Path type: copy (blender copies texture file to destination folder) 
-    * Open the OBJ file (the texture file will be automatically loaded) + 
-    * Optionally make hollow, put in holes and perform pre-print checks +===== In 3D Sprint: ===== 
-    * Export 3D model as VRML (.wrl) file. (The texture file will be exported as well) + 
-  * **In 3DPrint:** +  * Open the OBJ file (the texture file will be automatically loaded) 
-    * open the exported .wrl file and check if the texture is present. +  * Optionally make hollow, put in holes and perform pre-print checks 
-    * place on the build platform and start printing+  * Export 3D model as VRML (.wrl) file. (The texture file will be exported as well) 
 + 
 +===== In 3DPrint: ===== 
 + 
 +  * open the exported .wrl file and check if the texture is present. 
 +  * place on the build platform and start printing
  
  
  • projet_cjp_660/blender_workflow_for_color_printing.txt
  • Last modified: 2020/02/25 00:19
  • by formlab