Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
axidraw:axidraw [2020/05/25 04:36] – formlab | axidraw:axidraw [2023/05/10 07:57] – [Setup the Axidraw] formlab | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Axidraw ====== | ====== Axidraw ====== | ||
+ | |||
+ | |||
{{: | {{: | ||
- | A3 pen plotter. | + | A3 pen plotter. |
+ | |||
+ | ===== Quick Setup ===== | ||
+ | This is a condensed version. To learn more, here is the [[https:// | ||
+ | |||
+ | [[prepare_your_drawing: | ||
+ | ==== Install the software ==== | ||
+ | - Install [[https:// | ||
+ | - Install the [[https:// | ||
+ | |||
+ | ==== Setup the Axidraw ==== | ||
+ | - **FIRST**: Move the AxiDraw to its Home Corner: \\ {{: | ||
+ | - **AFTER** Axidraw is homed: Plug in the power. | ||
+ | - Plug in the USB connector. | ||
+ | - All USB plugs seem to work: in the back of the computer (iMac), in the keyboard, in a usb hub... | ||
+ | - Add a pen to the pen holder. | ||
+ | - Position your paper with its upper-left corner below the pen tip. | ||
+ | - Open Inkscape | ||
+ | - Select the drawing or text and select '' | ||
+ | - '' | ||
+ | - Adjust the pen's height | ||
+ | - Try to keep the range of movement to a minimum. This will draw faster and is better for the servo motor. | ||
+ | - '' | ||
+ | - Each visible layer will print. | ||
+ | - To pause or stop, press the metal button on the left side of the controller: | ||
+ | |||
+ | Vertical documents in Inkscape will be rotated left 90° on the Axidraw:\\ | ||
+ | {{: | ||
+ | |||
+ | For single line fonts, check Inkscape '' | ||
+ | |||
+ | Download the manual [[https:// | ||
+ | |||
+ | |||
+ | ===== Maintenance ===== | ||
+ | |||
+ | ==== Tightening the V-slot wheels ==== | ||
+ | {{: | ||
+ | When the Axidraw arm feels wobbly, tighten the eccentric nuts on the carriage to firm up the motion. | ||
+ | |||
+ | === Locations of the eccentric nuts === | ||
+ | {{: | ||
+ | The big wheels on the X-axis can be tightened here. Use a number 10 wrench. Only 2 big wheels need tightening. | ||
+ | |||
+ | {{: | ||
+ | The smaller wheels on the Y-axis can be tightened here. Use a number 8 wrench. Only 2 small wheels need tightening. | ||
+ | |||
+ | === Procedure === | ||
+ | * No need to loosen any bolts first. | ||
+ | * Turn the eccentric nut one way or another. The direction doesn' | ||
+ | * Work in small increments and feel with 1 finger if one of of the V-slot wheels can be rotated so it's slipping. If the wheels rotates, tighten the eccentric nut a little more and test again. When it's snug against the aluminum profile and doesn' | ||
+ | * Wait 15 minutes and move the axes back and forth carefully. Feel for little bumps. If the tension was set too high, the wheels could be squished a little, resulting in bumps. If so, release some tension, wait another 15 minutes and feel for bumps again. | ||
+ | |||
+ | Based on [[https:// | ||
+ | |||
+ | |||
- | 3 available |