Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
formech_1372:formech_1372 [2021/01/26 01:56] – [Machine settings] formlab | formech_1372:formech_1372 [2023/12/18 00:46] – [Control panel] formlab | ||
---|---|---|---|
Line 11: | Line 11: | ||
* Small: '' | * Small: '' | ||
* Large: '' | * Large: '' | ||
+ | |||
+ | === Pre-drying === | ||
+ | * PMMA: 70°C 4 hours | ||
+ | |||
[[https:// | [[https:// | ||
---- | ---- | ||
+ | |||
+ | ===== Mould tips ===== | ||
+ | |||
+ | <WRAP center round important 60%> | ||
+ | Moulds should not contain moisture or dust (!) since it could harm the vacuum pump. | ||
+ | </ | ||
+ | |||
+ | |||
+ | * Can the mould be removed after forming? | ||
+ | * {{: | ||
+ | * {{: | ||
+ | * {{: | ||
+ | * Include draft angles:\\ {{: | ||
+ | * Can the vacuum reach all pockets? | ||
+ | * {{: | ||
+ | * Can it withstand the pressure? | ||
+ | * Can it withstand the heat? | ||
+ | ==== Tested mould materials include: ==== | ||
+ | * **Plaster** | ||
+ | * <color orange> | ||
+ | * **Wood** | ||
+ | * <color orange> | ||
+ | * **PU foam** | ||
+ | * <color orange> | ||
+ | * <color green> | ||
+ | * <color green> | ||
+ | * <color green> | ||
+ | * <color green> | ||
+ | * <color red> | ||
+ | * <color red> | ||
+ | * **3D printed parts** | ||
+ | * <color red> | ||
+ | * Plastic deforms: infill becomes visible if not enough top layers or walls. | ||
+ | * ... | ||
===== Available sheet materials ===== | ===== Available sheet materials ===== | ||
Line 22: | Line 60: | ||
^ Thickness ^ Size ^ Cost (per sheet) ^ | ^ Thickness ^ Size ^ Cost (per sheet) ^ | ||
- | | 1mm | Large - 1370 x 660mm | €13,00 | | + | | 1mm | Large - 1370 x 660mm | €16,10 | |
- | | 1mm | Small - 500 x 500mm | €3,90 | | + | | 2mm | Large - 1370 x 660mm | €32, |
- | | 2mm | Small - 500 x 500mm | €6,63 | | + | | 1mm | Small - 500 x 500mm | €4,20 | |
- | | 3mm | Small - 500 x 500mm | €9,62 | | + | | 2mm | Small - 500 x 500mm | €7,14 | |
+ | | 3mm | Small - 500 x 500mm | €10,36 | | ||
---- | ---- | ||
Line 36: | Line 75: | ||
^ Color ^ Light ^ Thickness | ^ Color ^ Light ^ Thickness | ||
- | | White | translucent | 3mm | large - 1370 x 660mm | €36,40 | | + | | White | translucent | 3mm | large - 1370 x 660mm | €39,20 | |
- | | White | translucent | 3mm | small - 500 x 500mm | €10,40 | | + | | White | translucent | 3mm | small - 500 x 500mm | €11,20 | |
- | | Green | transparent | 3mm | small - 500 x 500mm | €15,60 | | + | | Green | transparent | 3mm | small - 500 x 500mm | €16,80 | |
- | | Light blue | translucent | 3mm | large - 1370 x 660mm | €54,60 | | + | | Light blue | translucent | 3mm | large - 1370 x 660mm | €58,80 | |
- | | Light blue | translucent | 3mm | small - 500 x 500mm | €15,60 | | + | | Light blue | translucent | 3mm | small - 500 x 500mm | €16,80 | |
- | | Dark blue | transparent | 3mm | large - 1370 x 660mm | €54,60 | | + | | Dark blue | transparent | 3mm | large - 1370 x 660mm | €58,80 | |
- | | Dark blue | transparent | 3mm | small - 500 x 500mm | €15,60 | | + | | Dark blue | transparent | 3mm | small - 500 x 500mm | €16,80 | |
- | | Yellow | transparent | 3mm | small - 500 x 500mm | €15,60 | | + | | Yellow | transparent | 3mm | small - 500 x 500mm | €16,80 | |
- | | Cream | transparent | 3mm | large - 1370 x 660mm | €54,60 | | + | | Cream | transparent | 3mm | large - 1370 x 660mm | €58,80 | |
- | | Cream | transparent | 3mm | small - 500 x 500mm | €15,60 | | + | | Cream | transparent | 3mm | small - 500 x 500mm | €16,80 | |
---- | ---- | ||
Line 56: | Line 95: | ||
^ Color ^ Surface finish | ^ Color ^ Surface finish | ||
- | | white | matte / glossy | 1mm | 2000X1200 | €18,20 | | + | | white | matte / glossy | 1mm | 2000X1200 | €19,63 | |
- | | white | matte / glossy | 1,5mm | 2000X1200 | €26,80 | | + | | white | matte / glossy | 1,5mm | 2000X1200 | €28,88 | |
- | | white | matte / matte | 4mm | 2000X1000 | €45,30| | + | | white | matte / matte | 4mm | 2000X1000 | €63,42| |
- | | black | matte / matte | 1mm | 2000X1200 | €20,50 | | + | | black | matte / matte | 1mm | 2000X1200 | €22,06 | |
- | | black | matte / glossy | 1,5mm | 2000X1200 | €32,70 | | + | | black | matte / glossy | 1,5mm | 2000X1200 | €35,19 | |
- | | red | matte / matte | 1mm | 2000X1200 | €20,50 | | + | | red | matte / matte | 1mm | 2000X1200 | €22,06 | |
- | | red | matte / glossy | 1,5mm | 2000X1200 | €32,70 | | + | | red | matte / glossy | 1,5mm | 2000X1200 | €35,19 | |
- | | green | matte / matte | 1,5mm | 2000X1200 | €31,60 | | + | | green | matte / matte | 1,5mm | 2000X1200 | €34,03 | |
- | | blue | matte / glossy | 1,5mm | 2000X1200 | €32, | + | |
=== How much does it cost? === | === How much does it cost? === | ||
Line 76: | Line 114: | ||
* startup cost: €2: only when vacuum form machine is used | * startup cost: €2: only when vacuum form machine is used | ||
* plastic sheet cost: cost sheet, including VAT and transportation | * plastic sheet cost: cost sheet, including VAT and transportation | ||
- | * material multiplier: 30%: item cost * 1,3 | + | * material multiplier: item cost * 1,4 |
- | * machine time cost: €5 per hour (€0, | + | * machine time cost: €8 per hour (€0, |
Line 142: | Line 180: | ||
* Narrow heating band | * Narrow heating band | ||
* will crystallise if over heated | * will crystallise if over heated | ||
- | |||
===== General tips ===== | ===== General tips ===== | ||
Line 148: | Line 185: | ||
* // | * // | ||
* // | * // | ||
+ | * **Bubble moulding**: The table should be lowered. If it's in the up-position, | ||
+ | |||
+ | ===== Drying sheets with the oven ===== | ||
+ | |||
+ | Use one of the ceramics oven in the metal atelier.\\ | ||
+ | The control cabinet is behind the oven. \\ | ||
+ | {{: | ||
+ | |||
+ | |||
+ | Get the key from Peter to be able to power on the oven.\\ | ||
+ | To turn on the oven, insert the key and turn it to the right. Then turn the red knob to the right.\\ | ||
+ | |||
+ | ==== Control panel ==== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | * There are 9 programs | ||
+ | * Each program can have multiple segments | ||
+ | * Example: segment 1: warm up to 70° in 30 min, segment 2: keep that temperature for 4 hours | ||
+ | * Each segment has 2 values: a temperature, | ||
+ | |||
+ | |||
+ | - Press ' | ||
+ | - Nothing is on here yet. (This might change in the future) | ||
+ | - Press until there' | ||
+ | - In the future there might be a paper with an explanation of what programs do what. I could have a fixed entry on the list | ||
+ | - Segment 1' is blinking. Use the up-down arrows to set a target temperature | ||
+ | - Press the --> arrow to go to the time value | ||
+ | - Set the time with the up-down arrows | ||
+ | - When ready, press the stop / start button to start the oven. | ||
+ | |||
+ | ==== Suggested program ==== | ||
+ | |||
+ | * Segment 1: temp: 70° time: 30 min | ||
+ | * Segment 2: temp: 70° time: 4 hours | ||
+ | * Segment 3: temp: 0° time: 30 min | ||
===== Clamping tips for high gauge sheets ===== | ===== Clamping tips for high gauge sheets ===== | ||
* Apply 80 grit strips of sand paper to the underside of the clamp frame to provide more grip on the sheet. The strips can be held in place with a good quality double sided tape, contact adhesive or preferably a silicone adhesive to take the heat. | * Apply 80 grit strips of sand paper to the underside of the clamp frame to provide more grip on the sheet. The strips can be held in place with a good quality double sided tape, contact adhesive or preferably a silicone adhesive to take the heat. | ||
Line 157: | Line 230: | ||
- | ===== Machine | + | ===== Machine |
- | === PMMA 3mm === | + | |
- | * heater 75% en 80% | + | |
- | * 230 sec heating (not any longer) | + | |
- | * 60 sec cooling | + | |
- | * --> Worked reasonably well | + | |
- | * --> This is lower heat for a longer period | + | |
- | === Medium Gauge Film (0, | + | ==== PS ==== |
- | * profile: 1mm PET (heater 85%) | + | * 1mm (Experimental v2) |
- | * heating: 8 seconds | + | * Power: 70% |
- | * vacuum: manual operation: start-stop technique to avoid holes if there are large cavities | + | * Heating: 45 seconds |
+ | * 2.5mm (Experimental v2) | ||
+ | * Power: 70% | ||
+ | * Heating: 85 seconds | ||
+ | |||
+ | ==== PETG ==== | ||
+ | * 2mm (OK) | ||
+ | * Power: 70% | ||
+ | * Heating: 70 seconds | ||
+ | |||
+ | ==== PMMA ==== | ||
+ | * 3mm | ||
+ | * pre-dry: 4 hours at 70°C (between 70-80°C): no blisters | ||
+ | * If using the window: add shims: 3 on each side. | ||
+ | * heater 70% (and 75% at the edges) | ||
+ | * 125 sec heating | ||
+ | * (without peeking in between) | ||
+ | * This results in ±168°C: nice and flexible. | ||
+ | * Sheet forming temperature: | ||
+ | * 60 sec cooling | ||
+ | |||
+ | |||
+ | ==== Medium Gauge Film ==== | ||
+ | | ||
+ | | ||
+ | * heating: 8 seconds | ||
+ | * vacuum: manual operation: start-stop technique to avoid holes if there are large cavities | ||
---- | ---- | ||
+ | |||
+ | ===== Troubleshooting ===== | ||
+ | ==== Preset loading gives wrong values ==== | ||
+ | |||
+ | Reason of problem: touch screen input is too fast for the slow computer (PLC) | ||
+ | |||
+ | Fix: | ||
+ | * **Use firm, deliberate presses with your finger** (not a stylus or fingernail). | ||
+ | * Don’t try to be too fast. | ||
+ | |||
+ | |||
+ | ==== Sheet pulls itself out of the clamping frame ==== | ||
+ | // | ||
+ | |||
+ | {{: | ||
+ | If you are using a reducing window, then you will have to make sure that you have good clamping on each side of the aperture. The reducing window seals are flat silicone sponge and do not have the same gripping effect as the round silicone bead seal. | ||
+ | |||
+ | {{: | ||
+ | // | ||
+ | |||
+ | ==== Blisters appear on the surface ==== | ||
+ | There is moisture in the sheet. At the point the blisters appear, the sheet is not hot enough to form yet. You'll need to dry the sheet or switch to a non hygroscopic material. | ||
+ | |||
+ | ==== Pre-stretch button does nothing ==== | ||
+ | * Turn off air supply | ||
+ | * Turn off Formech | ||
+ | * Wait ±1 minute and turn Formech back on. | ||
+ | * If you can hear the relay click, it works and the air supply can be opened again. | ||
+ | |||
+ | ==== Heater timer doesn' | ||
+ | * Enable the heater. (The timer doesn' | ||
+ |