Instructions - hyrel

bees_wax

Anonymous (anonymous@undisclosed.example.com) — 2020-10-13T12:34:17+00:00

Bees Wax Cleaning * hold part with pliers * heat up with very hot water * Wipe off with paper towel * Clean threads with a toothpick or a metal pin Settings / profiles * 1,6w 0,2z 15f 0pct * 3D object: Cone * 35°C filament, no fan, no bed

emo-25

Anonymous (anonymous@undisclosed.example.com) — 2020-10-13T13:50:02+00:00

EMO-25 * 25cc. * pastes, gels, liquids. * Nozzle sizes: 1.0, 1.5, 2.0mm (and Luer adaptor needles) * results are not edible. * Official info: * Toolchange for bigger prints: Press the big pause-button and remove the tool head. When changing the tube, use the presetter tool to make sure the new tube has the same nozzle offset then the previous one.

errors

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:28:58+00:00

Errors * Missing Z-steps during layer change * Z-travel feed is too high. Set all Z-feeds to max 180(mm/s?) * go to Slic3r > pint settings > Speed settings > travel settings and set travel speed to 3mm/s

general_slicer_info

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:26:23+00:00

General Slicer info * Slic3r profile files are stored in C > Users > Elias Heuninck > AppData > Roaming > Slic3r > print * This way they can be found & loaded by the Repetrel sofware. * Hyrel standard recipe naming convention: 0.5w, 0.2z, 30f, 35pct.ini

hyrel

Anonymous (anonymous@undisclosed.example.com) — 2021-01-26T09:38:54+00:00

Hyrel Modular system with both FDM and extrusion of emulsifiable materials (a.k.a a paste or gel printer). * Max Build Volume: 225 x 200 x 200mm Tutorial * Your first print Reference * Prepare the machine * Level the bed * General slicer info * Start a print * Tips * Errors --- * Clean cylinders after each use! Not doing so will ruin them.

level_the_bed

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:07:21+00:00

Level the bed Also called 'tramming'. * Remove any tools from the yoke * Attach glass build plate with blue tape. Keep the screws in reach. * Home the X & Y axes * Go to the park location * Check the probe-battery . The screen should light up when the probe is pushed in.

luer-tips

Anonymous (anonymous@undisclosed.example.com) — 2020-10-12T15:00:33+00:00

Luer Tips in mm Outside Inside Olive 2,1081,753Grey 1,6401,200White 1,4731,219Pink 0,9100,600Blue 0,6350,406

mk1-250

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T12:05:53+00:00

MK-250 * Official info:

plasticine

Anonymous (anonymous@undisclosed.example.com) — 2020-10-12T13:26:37+00:00

Plasticine Keep temperature in mind. Plasticine will under-extrude when below room temperature (±20°C). Loading material * Push the piston to the other end of the tube. Do not fasten the rear collar yet. * Warm up plasticine in your hands and push it into the tube. Make sure that

prepare_the_machine

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:06:14+00:00

Prepare the machine * Power on * Turn on the power supply on the left side of the machine. * Turn on the machine by pressing the round metal power-button on the left bottom of the front panel: * Make connection * Open Repetrel on the computer (Repetrel is not running on the tablet anymore).

start_a_print

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:27:57+00:00

Start a print * Load in a 3D file * Set the slicer profiles * Click the big Process button & select Slice with Slic3r. * When the G-code preview looks good, click Print * Use Z fine adjust (Z+ = bed closer to nozzle, Z- = bed further away from nozzle)

tips

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T12:47:17+00:00

Tips * Cylinders can be combined for larger volume prints. * M0 x0 y200 (Pauses the print and brings the tool head forward so the current cylinder can be swapped out for a new one. When ready, press continue). * Keep cylinders CLEAN. Dry material inside is the #1 problem.

vol-25

Anonymous (anonymous@undisclosed.example.com) — 2020-10-06T11:52:40+00:00

VOL-25 Official info: Loading Cylinder * Unscrew the cylinder front collar * Slide cylinder down in the toolholder * Tighten the 3 bolts of the toolholder * Reattach front collar to the cylinder Removing Cylinder * Unscrew the cylinder front collar

your_first_print

Anonymous (anonymous@undisclosed.example.com) — 2020-10-12T13:39:05+00:00

Your first print Formlab todo: add more pictures 1. Prepare the printer * Power on * Turn on the computer. * Turn on the power supply on the left side of the machine. * Turn on the machine by pressing the round metal power-button on the left bottom of the front panel: