3devo_extruder:3devo_extruder

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
3devo_extruder:3devo_extruder [2020/09/10 06:59] formlab3devo_extruder:3devo_extruder [2021/09/30 07:32] (current) – [Troubleshooting] formlab
Line 27: Line 27:
    
 ===== Dry filament ===== ===== Dry filament =====
-  * 4-6 hours @70-80°C.  +  * 4-6 hours @70-80°C. Stir regularly.
-  * Other sources say to stay below 40°C+
  
  
Line 52: Line 51:
 This is a simple methodology to get you started. This is a simple methodology to get you started.
  
-{{:3devo_extruder:schematic-overview-of-extrusion-system.png?200|}} +{{:3devo_extruder:schematic-overview-of-extrusion-system.png?400|}}
- +
-Source of info  +
-  * [[https://www.youtube.com/watch?v=uxp2iuypDAo&feature=youtu.be]] +
-  * [[https://support.3devo.com/filament-thickness-deviation-inconsistent-diameter]]+
  
   * Enter dimensions of spool into the settings panel   * Enter dimensions of spool into the settings panel
Line 66: Line 61:
     * Fan: 50%. Changes to the cooling have a big impact on the filament.     * Fan: 50%. Changes to the cooling have a big impact on the filament.
   * Apply the settings   * Apply the settings
-  * Start logging with Devovision+  * Start logging with [[https://3devo.com/devovision/download/|DevoVision]]
   * Start extrusion.    * Start extrusion. 
     * Check for unmelted particles (too cold)     * Check for unmelted particles (too cold)
Line 80: Line 75:
     * //It's yet unclear to me how to determine a profile, or why it's necessary instead of using all heaters at the same temperature.//     * //It's yet unclear to me how to determine a profile, or why it's necessary instead of using all heaters at the same temperature.//
   * If you are dealing with **filament deviation**, the first temperatures to experiment with are the temperatures of heater 1 and 4. Also make sure that the material will be fully melted when entering the metering zone of the extruder.   * If you are dealing with **filament deviation**, the first temperatures to experiment with are the temperatures of heater 1 and 4. Also make sure that the material will be fully melted when entering the metering zone of the extruder.
 +  * check if your granulate is pure. Contaminants (a pellet of a different polymer for example) might partially block the flow.
 +  * Purge the machine with DevoClean might make the extrusion more consistent.
 +  * Feed material regularly. Avoid big changes in hopper loading.
  
 +Cooling:
 +  * too much cooling makes the filament too rigid. This makes it impossible to control the diameter
  
 +Extruder RPM: 
 +  * output rate of the material
 +  * If the extruder speed is inconsistent, so will the material output rate. It will be very difficult for the puller mechanism to maintain a consistent filament thickness when the extrusion rate is inconsistent.
 +  * Extruder speed inconsistency can be caused by different things:
 +    * Wrong temperature profile;
 +    * Material feeding issues;
 +    * Material contamination;
 +    * Polymer degradation
 +  * Reducing the Extruder speed gives the puller mechanism more time to react, which results in more stable extrusion
 +
 +Winder mechanism:
 +  * needs to be easily stoppable with 1 finger (adjust slip clutch on the back). If it pulls too hard, it overrides the control of the puller mechanism.
 +
 +
 +Source of info 
 +  * [[https://www.youtube.com/watch?v=uxp2iuypDAo&feature=youtu.be]]
 +  * [[https://support.3devo.com/filament-thickness-deviation-inconsistent-diameter]]
  
  
 ===== Recycling plastic ===== ===== Recycling plastic =====
-[[https://www.youtube.com/watch?v=l9OuNUuVbdI|link]]+
   * keep waste plastic waste away from moisture, UV light, dust or grease   * keep waste plastic waste away from moisture, UV light, dust or grease
   * sort different polymers. Only work with 1 kind at a time   * sort different polymers. Only work with 1 kind at a time
Line 92: Line 109:
   * extrude   * extrude
   * print   * print
 +
 +Source: 
 +  * [[https://www.youtube.com/watch?v=l9OuNUuVbdI|link]]
 +
 +
 +===== Powder based pigments / fillers =====
 +
 +  * The Pigment Dunaliella Salina comes in a range of particle sizes. When mixing with PLA pellets, shake the batch well, then repetitively move the pot back and for on a table so the large particles sink down and the fine ones stick to the pellets on top. The fine powder colours the PLA darker orange and the filament has almost no speckles. Filament batches from further down the mixture are more yellow with more speckles. **Make sure to only very lightly coat the PLA pellets with pigment powder. Too much powder and the extrusion won't be consistent.**
 +
 +
 +===== Troubleshooting =====
 +
 +  * **The diameter never settles and is way too big and then too small.** 
 +  * **The filament feels rather stiff when handling.**
 +  * **Sometimes blobs of pure pigment appear, throwing off the diameter sensor.**
 +If this happens with fillers (Plastic pellets with added non-plastic parts, for example Algae powder pigments), **reduce the amount of powder** added to the PLA pellets. I used 25g of Dunaliella Salina for 750g PLA. But this was too concentrated. For every 100g coated PLA pellets, I added 120g clean PLA pellets. Then I mixed them for a few minutes thoroughly with a spoon. The extruded filament is dimensionally stable and feels much more supple when handling.
  • 3devo_extruder/3devo_extruder.1599746345.txt.gz
  • Last modified: 2020/09/10 06:59
  • by formlab