Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| projet_cjp_660:projet_cjp_660 [2021/08/25 05:54] – formlab | projet_cjp_660:projet_cjp_660 [2022/09/30 02:01] (current) – [Pre print checks] formlab | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| {{: | {{: | ||
| + | |||
| + | ===== 3D modelling workflow ===== | ||
| + | |||
| + | * [[projet_cjp_660: | ||
| + | |||
| + | |||
| + | Issue with lines on texture in 3D Print (not visible in Blender): https:// | ||
| + | - hmm.. texture was 2x2k. Try maybe a UV render with larger spaces between the islands? | ||
| + | |||
| Line 8: | Line 17: | ||
| * Check power status print-computer. No sleep or screen saver. | * Check power status print-computer. No sleep or screen saver. | ||
| * Raise build plate (!) | * Raise build plate (!) | ||
| + | * Clean the parking caps. | ||
| + | * Clean the service station. | ||
| + | * Clean the spreader roller and scrapers. | ||
| + | * Clean the fast axis rails and carriage. | ||
| + | |||
| ==== Post print steps and cleaning ==== | ==== Post print steps and cleaning ==== | ||
| - | * Leave print in build chamber for x minutes (LOOK UP DURATION) | + | * Leave print in build chamber for 2 hours to strengthen the glue. |
| - | * Vacuum excess core material | + | * Vacuum excess core material. |
| - | * Raise buildplate | + | * Raise buildplate. |
| - | * Clean the debris separator grille | + | * Clean the debris separator grille. |
| - | * Clean the parking caps | + | * Clean the parking caps. |
| - | * Clean the service station | + | * Clean the service station. |
| - | * Clean the spreader roller and scrapers | + | * Clean the spreader roller and scrapers. |
| - | * Clean the fast axis rails and carriage | + | * Clean the fast axis rails and carriage. |
| ==== Cleaning print ==== | ==== Cleaning print ==== | ||
| Line 42: | Line 56: | ||
| * A funnel | * A funnel | ||
| * A downdraft table or fume hood for ventilation | * A downdraft table or fume hood for ventilation | ||
| - | * Place a sheet of non-stick material (Te * Have a good supply of paper towels ready for absorbing excess ColorBond. | + | * Place a sheet of non-stick material (Te�on, freezer paper or wax paper) on your work area for easy clean-up and to put your parts on as they cure. |
| + | * Have a good supply of paper towels ready for absorbing excess ColorBond. | ||
| * The workstation should be well lit. | * The workstation should be well lit. | ||
| * **Dip** | * **Dip** | ||
| Line 65: | Line 80: | ||
| * Post Processing | * Post Processing | ||
| * Sanding | * Sanding | ||
| - | * Start with 100-grit paper and continue to 220-grit if a smoother | + | * Start with 100-grit paper and continue to 220-grit if a smoother |
| - | * Parts in * Joining | + | |
| - | * For a plastic-like fi | + | * Parts in�ltrated with ColorBond can be painted without additional processing. For the best surface �finish, sand lightly, use a primer, and then apply paint. |
| + | * Joining | ||
| + | * For a plastic-like fi�nish, �fill in the seam of joined parts with Bondo® No.907 Glazing Spot Putty, apply 1-2 coats primer, sand lightly, and paint. | ||
| Storage: | Storage: | ||
| Line 76: | Line 94: | ||
| - | * [[projet_cjp_660: | + | ===== How much does it cost? ===== |
| - | + | ||
| - | + | ||
| - | Issue with lines on texture in 3D Print (not visible in Blender): https:// | + | |
| - | - hmm.. texture was 2x2k. Try maybe a UV render with larger spaces between the islands? | + | |
| - | + | ||
| - | + | ||
| - | === How much does it cost? === | + | |
| ( build material cost ) * material multiplier ) | ( build material cost ) * material multiplier ) | ||